Garage doors are normally installed with two types of springs, one a torsion spring and the other is extension spring. The torsion springs are positioned right above the opening of the garage door to balance its weight while opening and closing.

These springs are secured with a metal rod and shaft that runs throughout the springs. The decision is also depended upon the design and material of the garage door. These springs hold the majority of the weight of the garage door while opening and closing. The garage door springs are installed with other hardware to function together, enabling you to open and close the big garage door smoothly. Whenever you face issues with garage door springs, you should consult professional garage door technicians. 

If you find it hard to open and close the garage door, then there is most likely an issue with the operating system of the garage door. If you have a double spring system, you should call a local garage door expert to ask about the double garage door spring repair cost and do the fixes instead of handling it on your own. It is extremely risky if you do the job by yourself especially if it is a double torsion spring system. As you know, even the normal springs are created to keep the structure and store the pressure for a long. Garage door torsion springs have the same characteristics and the pressure present inside the springs is better understood by professional garage door technicians so you should leave these projects to them.  

You could perform some earlier checkups on your garage door springs such as, removing the accumulated grease and dirt from tracks and rollers. These substances could have caused problems with the smooth operations of a garage door. You can inspect the hardware of the garage door to make sure that there is no loosening, rusty, or damaged garage door part and tighten and replace them accordingly, but when it comes to garage door springs, adjusting and replacing should be done by those who know the ins and outs of garage door spring system.  As they hold a great amount of pressure, adjusting them can be dangerous as it can give you serious injuries.

If you are interested in handling garage door springs alone, there are some points that you need to follow. Remember that fixing and replacing the garage door torsion springs can be extremely dangerous. First of all, you need to make sure that you have the correct replacement part.

There are multiple springs under one category of springs available in the market; therefore, you need to make sure that you have the correct spring. Don’t forget to release the tension from the old spring before moving it and installing the new ones. Never touch the cable drums and cones. Afterward, insert the fitting bars into the winding cones before unscrewing anything. You need to hold the bar inside the cones during the replacement project. Never touch the mounting brackets when you wound the springs. If you have any confusion or question, contact local garage door specialist.

Getting broken garage door springs replaced could be one phone call away do not waste your time asking them for expert assistance about this problem. It is not wise to risk yourself and your family just to save some dollars.

When you are experiencing the issue of broken garage door springs that need to be replaced you can either call professional garage door technicians or do it on your own.

Garage door springs are long, heavy, and hard-to-handle devices that are used to lift and lower the weight of the garage door.  Garage door torsion spring installation can be a hard and challenging process that should be left to professional garage door experts. If your garage door has broken springs that need to be taken care of you should exercise all required safety measurements. The following mentioned are the steps that you can follow to get the job done in the right way. These points will also help you to ensure that the project can be done easily and the garage door will work properly.

The most important point that you need to keep in mind is to ensure that you have disconnected the power supply to the garage door so you do not get electrocuted while performing the work. You should turn off the power cord of the garage door opener along with disconnecting it from the garage door. This rule is for newer garage door models. With older models of garage doors, you may need to remove the fuse or turn off the circuit breaker to disconnect the power supply.

Look closely at the broken garage door torsion spring and the new one to make sure that they are both the same. Confirm that both of them are the same in type, size, and dimension to make the garage door functional smoothly. While picking a new spring, avoid grabbing them with each other. Don’t touch the winding cones of the new springs for your personal safety. Use any writing instrument to mark the torsion shaft ends. You need to do it because it helps you to make sure that you have a properly aligned garage door when you have completed the project of broken garage door spring replacement.

Wind the unbroken spring off and unfasten the screws and bolts that are used to secure the torsion cones and spring mounting brackets together. Then remove the bolts completely. Once you have completed the process of removing the broken garage door spring, it is time to install a new spring along with installing the hardware. Once you have done the process, it is time to wind up the new spring. After finishing the entire task, you need to check and test the garage door to make sure that the garage door is balanced correctly. In order to reduce the amount of friction, you need to apply some lubrication.

Once you have checked the garage door make sure that it is aligned correctly and all the components are tightened and in place. It is time to reconnect the garage door opener. It is true that you should not play with the garage door but you need to open and close the garage door a few times to make sure it is working correctly. it is easy to replace the broken garage door springs on your own if you have the right skills and tools. You need to make sure that you are doing a job correctly because it can be dangerous if you are not careful. You could lose your hand, legs, or even life. Therefore, it is suggested to call professional help.